| English | Japanese |
|
|
Access until yesterday |
| Introduction. | [Lily Diary] Diary of Life in Mindanao |
| 25/06/07 | Introducing the Shack |
| 25/06/06 | A portrait illustrated by ChatGPT |
| 25/05/26 | Windows full-width half-width switching |
| 25/05/17 | OK2ZAW BCD to 16 converter |
| 25/05/16 | For 3.5MHz zepp antennas Stepping motor this and that |
| 25/05/15 | 3.5MHz stepping motor plan |
| 25/05/14 | 3.5MHz tuning coil installed |
| 25/05/11 | 3.5MHz antenna installation completed |
| 25/05/03 | JTDX automatic operation program Ver0.4.3 |
| 25/04/26 | Drone Habsan ZINO |
| 25/04/25 | Time setting Ver0.3 |
| 25/04/24 | AutoCWType_Ver1.3 |
| 25/04/23 | FTDX3000 LCD repair preparation |
| 25/04/22 | Installation plan for 3.5 MHz Twep antenna |
| 25/04/21 | AutoCWType_Ver1.1 |
| 25/04/20 | 10,14MHz antenna installation completed |
| 25/04/19 | JTDX automatic operation program Ver0.4.1 |
| 25/04/19 | Antenna pole installation at 14 MHz |
| 25/04/18 | ThinkPad X390 repair completed |
| 25/04/17 | Search is now available. |
| 25/04/15 | Preparation of 10 MHz dipole |
| 25/04/12 | Hexbeam Part8 |
| 25/04/06 | ThinkPad X390 is broken. |
| 25/04/05 | Time Setting Program |
| 25/03/31 | JTDX Automatic Operation Program |
| 25/03/30 | Automatic log sending from CWType to Hamlog |
| 25/03/21 | Hexbeam Part7 |
| 25/03/20 | FreeDV Part3 First QSO |
| 25/03/18 | FreeDV Part2 QSO in shack |
| 25/03/16 | Hexbeam Part6 |
| 25/03/15 | FreeDV Part1 installation |
| 25/03/09 | Hexbeam Part5 |
| 25/03/07 | Hexbeam Part4 |
| 25/03/05 | 28MHz antenna modification |
| 25/03/01 | FTDX3000 is broken! |
| 25/02/28 | Pile up at 50MHz FT8 |
| 25/02/28 | DXV500ZS linear amplifier repair |
| 25/02/27 | Pipe and rebuild plan for tower |
| 25/02/26 | Direction of Japan from Ozamiz |
| 25/02/26 | 28MHz does not fly. |
| 25/02/23 | DXV500ZS linear amplifier repair |
| 25/02/22 | Hexbeam Part3 |
| 25/02/21 | Hexbeam Part2 |
| 25/02/18 | 28MHz antenna construction |
| 25/02/17 | 18,24MHz antenna height construction |
| 25/02/16 | Z26NS Cosovo |
| 25/02/14 | 21MHz FT8 |
| 25/02/12 | Antenna repair at 7,21 MHz |
| 25/02/08 | CW operation at 21MHz |
| 25/02/05 | DXV500ZS linear amplifier failure |
| 25/01/19 | Input Director |
| 25/01/14 | Temporary License Renewal |
| Automatic antenna switching (2025/05/17) | ||||
|---|---|---|---|---|
I am using the now defunct MFJ/AMERITRON Remote Coax Switch RCS-10
After switching the band of the radio with four antennas to switch. I often accidentally forget to switch the RCS-10 antenna switcher So I was searching the Internet for a solution to solve the problem. OK2ZAW Jan Sustr'sHamparts.shopindicates certainty, emphasis, etc.BCD to 16 converterI found something called Product to obtain 16-point output from BANDDATA at LINEAR terminal of YAESU radio manual 69 euros approx. 11,000 yen 4,300 pesos  |
||||
| Ordered after numerous email exchanges with OK2ZAW Jan Shipped Czech Republic (Czechia) on April 11 and arrived in Ozamiz on May 16  |
||||
| Wiring the 15-pin DSUB that was ordered together with the FTDX3000 while reading the FTDX3000 manual Switch the band from 1.9MHz to 50MHz and confirm that the INPUT to OUTPUT works properly  |
||||
Next, check the RCS-10 schematic that Jan sent me. |
||||
Fortunately, the RCS-10 has eight input terminals.BCD to 16 converterConnect the output of |
||||
| Since the antennas are 3.5 MHz, 7-21-28 MHz, 10-14 MHz, and 18-24 MHz Diode matrix wiring of signals to be input to antenna switcher.  |
||||
Dirty but diode aerial wiring |
||||
Completed in a Takachi TW9-6-17B case that I had previously purchased from Amazon Japan |
||||
| May 16, 2024 May 26, 2025 | ||||