JI1FGX/DU9 Mindanao, Philippines Amateur Radio Diary IOTA OC-130
English Japanese



Access until yesterday
Introduction. 【【Lily Diary]
Diary of Life in Mindanao

24/12/11 CVS conversion software for DXCC listings
24/12/05 Aggregation by country from JTDX
24/12/02 ADIF for one month from JTDX
Programs that create files
24/11/24 CwGet and CwType settings
24/11/24 WWDX Contest
24/11/21 CQ Ham Radio
24/11/20 Call Sign Assignment IOTA Number
24/11/13 IOTA 100 Awards Arrival
24/11/12 LoTW WAZ and DXCC
24/11/04 PLDT Optical Internet
24/10/30 Pile-up of 50MHz FT8
24/10/28 Camiguin Is Crowdfunding
24/10/26 50MHz Yagi feeder
24/10/21 RTTY with MMTTY
24/10/19 Firmware for UV-5K
24/10/17 Antenna group seen by drone
24/10/16 7MHz Antenna Pole
24/10/15 3.5MHz zepp transceiver antenna
24/10/14 Hexbeam Purchase Plan
24/10/13 24MHz dipole addition
24/10/13 50MHz Yagi repair completed
50MHz FT8 first pile
24/10/12 Antenna production for 24 MHz
24/10/09 Trouble with Gmail
24/10/09 The Shack
24/10/07 JO1CRA/7 AS-206
24/10/05 3D2V Rotuma Island IOC-060
24/10/01 Camiguin Island Trailer Video
24/09/30 Uruguay
24/09/29 50MHz antenna installation
24/09/25 Pile up on the caller's side
24/09/19 IOTA 100 Award
24/09/18 IOTA Application
24/09/12 DXCC Application
24/09/11 FT8 in communication with KH8T
24/09/08 50MHz Yagi Antenna
24/08/28 Pile up at FT8
24/08/07 Pile up from FT8EU
24/07/19 JW/WE9G in Svalbard
24/06/27 Purchase of air conditioner for wireless room
24/05/28 antenna switch
24/05/27 MFJ-259B Repair
24/05/10 Completed 3-band antenna
24/05/03 7MHz Dipole
24/04/30 7MHz Domestic
24/04/29 Reopening Project
24/04/04 Repair of FTDX3000
24/03/21 To NTC Cagayan
Firmware rewrite for UV-5K (October 19, 2024)
UV-5K Firmware Update (October 19, 2024)
I purchased a Quansheng UV-5K from Shopee, Philippines on April 23, 2024
Purchased for 999 pesos (2,700 yen) as a contact for making antennas.
VUHF transceivers can ONAIR on frequencies that cannot be transmitted in Japan!

On April 23, 2024, I purchased a Quansheng UV-5K from the Philippine e-commerce site Shopee.
I bought it for communication purposes while building antennas,.
for 999 pesos (approximately $17.5).
This VUHF transceiver can transmit on frequencies that are not allowed for transmission. for transmission
in Japan but is, of course, legal in the Philippines.
The model name UV-5K is not written anywhere on the box.
The model name "UV-5K" is not written anywhere on the box.
USB Programming Cable for Quansheng UV-K5
211 pesos ($570, $3.7) for two
We immediately rewrote the firmware.
First, download and extract Radio Cable Driver.zip and Firmware IJV.zip, k5prog_win-v1.26_IJV
I immediately proceeded with the firmware update.
First, I downloaded and extractedRadio Cable Driver.zip,Firmware IJV.zip, andk5prog_win-v1.26_IJV.
Install Radio Cable Driver to enable USB Programming Cable
The driver installation isINSTALLIt only takes a few seconds to press
Installing the USB driver is as simple as pressingINSTALL, and it only takes a few seconds.
Start the device manager and then plug the USB cable of the USB Programming Cable into the PC
After a few moments, the ports will be added as follows
After launching the Device Manager, plug the USB programming cable into the computer.
After a moment, the port will be added as shown below.
Once the COM port is recognized, plug in the connector on the radio side
I read on the internet that if you don't insert it deep enough, it may fail to be recognized.

Once the COM port is recognized, plug the connector into the radio.
I read on the internet that "if you don't push it in all the way, there may be a failure in recognition."
Start the programming program k5prog_win-v1.26_IJV.exe
Launch the programming programk5prog_win-v1.26_IJV.exe.
Select the Serial port that you have checked in the device manager.
Select the Serial port that you confirmed in the Device Manager.
Use these three buttons
Backup with Read Configuration and Read Calibration
Take a backup usingRead ConfigurationandRead Calibration.
Only Write Firmware requires UV-5K to be in programming mode.
To enter programming mode, turn on the UV-5K while holding down the PTT
The top LED glows white and nothing is displayed on the LCD panel.

Press the Write Firmware button to upload the unzipped firmware Firmware IJV_v2.9.R5.bin

Only forWrite Firmware, it is necessary to put the UV-5K into programming mode.
To enter programming mode, press the PTT on the UV-5K while turning on the power.
The LED on the top will light up white, and nothing will be displayed on the LCD panel.

Then, press theWrite Firmwarebutton
and upload the firmwareFirmware IJV_v2.9.R5.binThat you extracted earlier.
October 17, 2024   October 20, 2024